Comet multi-function colloid mill & grinder pump JW80/90/100/120/140/160/180/200/250/320/400/500 series than CM2000 series model specifications must be all. It is especially suitable for the shearing, homogenization and emulsification of fluid solutions and ultrafine suspensions, as well as the grinding and grinding of colloids and paste media. In addition to the high speed and flexible adjustable rotor clearance, JM operates under friction and is also known as wet grinding. There is a wide inlet gap and a narrow outlet gap between the conical rotor and the stator. During operation, the dispersing head is eccentrically operated to cause eddy currents in the solution, so that a better grinding and dispersing effect can be achieved. Iridium pipeline colloid mill, high shear mill, outlet mill, nano grinder, graphene grinder, pipeline mill JW80/90/100/120/140/160/180/200/250/320 The /400/500 series machine adopts the grinding and stator of the Zuijia geometric mechanism, and the good surface treatment and high-quality materials can meet the various needs of different industries.

Multi-functional colloid mill, pipeline type high-shear grinding pump, the material enters the high-shear crushing zone directly from the inlet under the high-speed rotation of the motor, and some large powder clusters, sticky blocks and clusters in the fluid are passed through a special crushing device. Particles of equal size and size are rapidly broken, and then sucked into the shear pulverization zone. In a very narrow working aisle, the rotor blade and the stator blade are relatively high-speed cut to generate strong friction and grinding and crushing. Under the action of mechanical motion and centrifugal force, the pulverized and refined material is re-pressed into the refining zone for grinding and crushing. The fine grinding is divided into three grades. The higher the precision of the first-stage grinding disc, the smaller the pitch, the longer the linear velocity, the finer and finer the material, and the fluid gradually curves toward the radial direction. The direction velocity of each fluid changes instantaneously, and is subjected to tens of millions of high-speed shears per minute, strong friction, extrusion grinding, particle pulverization, etc., in tens of millions of high speeds passing through three refining zones. After shearing, grinding and pulverizing, the liquid molecular chain breakage, particle pulverization, liquid particle tearing and the like are produced to fully achieve the purpose of dispersion, pulverization, emulsification, homogenization and refinement. The fineness of the liquid material can reach 0.5um. The three-way grinding zone, the first stage is the coarse grinding area, the second level is the fine grinding area, the third level is the ultra-fine grinding area, and the third level is the finished product.

   Features of the multi-functional colloid mill: 1 The fixed rotor is made into a circular cone shape with fine-grained three-stage, four-stage serrated protrusions and grooves. The stator can be adjusted without restriction to the required distance from the rotor. The depth of the 2 dentition: from the beginning of 2.5mm, 1.5 mm, 1 mm to the end of 0.03mm, the range is relatively large, the larger the range, the wider the particle size of the treated material. 3 The structural helical teeth of the groove, the groove depth of each grinding head is different, and the volume of the flow path of the helical tooth is from top to bottom from top to bottom. 4 evenly distributed. 5 can realize low temperature intelligent control and pipeline type automatic control, and the pipeline is pulverized and ground finely processed with a fineness of 1-10 micron. 6 This machine has a conveying function with a head of 10-40 meters and a pressure of 0.2-0.4MPa.

Compared with domestic and foreign equipment

 Contrast structure Grinding head structure Speed ??Linear speed Module head Seal type Product effect

Domestic and foreign equipment

The groove is a straight line, the groove depth of the same level is the same, or the disc type concave-convex parallel groove combination groove structure, the groove depth of each grinding head is different, and the flow path of the helical tooth is from the top to the bottom The bottom is from the big to the bottom, or the concave and convex parallel cogging is not adjusted by the inverter. The belt can accelerate the bearing. The bearing can withstand 140,000 RPM is 3-4 times of their speed, and the grinding force is 3-4 times of their strength. Through the frequency conversion adjustment, their bearings can not withstand high speed operation. Ultra-high transfer solution is highly sheared, friction is easy to heat, qualitative change, etc. Approximate classification: 10-20M/S

23-50M/S has only one module head or six kinds of dispersion emulsification without pulverization and grinding function. Single mechanical seal or shaft seal, high leakage failure rate, product leakage into the motor, causing motor burnout. Particle size is limited, 100 It is more difficult to be micron or less, and the repeatability is poor. If it can reach a small particle size of 1-10 micrometers, the material is re-agglomerated by high-speed friction dispersion.

The 溝槽星機械 The groove is a curve with different widths, depths and heights. The upper and lower shallow grades, each of the three 丶 four-stage helical teeth have different groove depths and structures of four and three stages. The track volume is as large and super-fine. The comet colloid mill is determined by the elastic coupling of the split bearing housing and the rigid coaxial synchronous drive for high precision and the precision of the internal structure of the third and fourth stages relative to the cone. It can be controlled by frequency conversion and the speed can reach above 2900 -3650RPM, so that the medium can be fully depolymerized, dispersed, homogenized, pulverized and ground to fineness. 20-40M/S can choose a variety of different module heads to achieve more Functions such as integrated design of three- and four-stage emulsification modules, high-speed hybrid propulsion module for batch powder liquid, continuous powder mixing module, three cooling, double cooling and improved three mechanical seals, easy to clean, will leak Reduced, can be operated 24 hours a day. It can realize low temperature intelligent control and pipeline automatic control. The fineness reaches 1-10 micron particle size, with conveying function, head 10-40 meters, pressure 0.2-0.4MPa.

Application areas:

Food industry: aloe vera, pineapple, sesame, fruit tea, ice cream, moon cake filling, cream, jam, juice, soybean, bean paste, bean paste, peanut milk, protein milk, soy milk, dairy products, malt extract, flavor, various beverages Wait.

Chemical industry: paints, pigments, dyes, coatings, lubricants, greases, diesel, petroleum catalysts, emulsified asphalt, adhesives, detergents, plastics, explosives, fiberglass, leather, emulsion explosives, etc.

Daily chemical: toothpaste, detergent, shampoo, shoe polish, high-grade cosmetics, bath essence, soap, balsam, etc.

Pharmaceutical industry: various types of syrup, nutrient solution, proprietary Chinese medicine, creamy agent, biological products, cod liver oil, pollen, royal jelly, vaccine, various ointments, various oral liquids, injections, intravenous drip, etc.

Construction industry: various coatings. Including interior and exterior wall coatings, anti-corrosion and waterproof coatings, cold porcelain coatings, colorful coatings, ceramic glazes, etc.

Paper industry: pulp, adhesive, rosin emulsification, papermaking auxiliaries, resin emulsification, etc.

Pesticide industry: fungicides, seed coating agents, herbicides, pesticide emulsifiable concentrates, chemical fertilizers, biochemical pesticides, biological pesticides, etc.

Other industries: textile industry, coal flotation agent, rare earth, nano material dispersion and depolymerization, reaction extraction and military industry.

about us:

    Wenzhou Haoxing Machinery Equipment Co., Ltd. was established in 1993 as a fluid manufacturer of Zhejiang Science and Technology SMEs, mainly serving global industry, biotechnology, food, dairy, beverage, pharmaceutical, chemical, petroleum, auxiliaries, petrochemical, Fine daily chemical, steam, water treatment systems and various types of fluid control systems, the company is committed to product design, research and development, manufacturing, sales of food machinery equipment, pharmaceutical machinery equipment, chemical machinery equipment, pumps, valves, accessories, to provide users with comprehensive Fluid control programs and development plans. The company is headquartered in China's Wenzhou Economic and Technological Development Zone with a large-scale factory. The company is mainly responsible for the supply of products to the UK, Italy, Germany, Asia, Africa and other regions, responsible for mainland operations and after-sales service.